This is the API V2 documentation. To switch out of beta revert back to our API V1.

Open SidemenuDocs
Docs
Close Sidemenu

How to Configure a Sansay SBChow-to-configure-a-sansay-sbc

Configuring your Telnyx Mission Control Portalconfiguring-your-telnyx-mission-control-portal

Step by Step Guidestep-by-step-guide

For step by step instructions on each of the requirements on the Telnyx Mission Control Portal, please follow this guideTelnyx Developers. Once you've configured your Telnyx account, you can now proceed to setup Sansay SBC following the guide below.

Configuring your Sansay SBCconfiguring-your-sansay-sbc

Step by Step Guidestep-by-step-guide

You are now all set on the Mission Control Portal side and are ready to configure your Telnyx trunk within your Sansay SBC system.

Define your Resource Settingsdefine-your-resource-settings

In order to configure the SIP server information for inbound & outbound trunks, navigate to Resources -> and create two new resources, one for each trunk.

Resource Type: Inboundresource-type--inbound

Resource Type: Peering

Protocol: SIP

SIP Profile: SIP_Peering:0

General Info:general-info-

SIP Trunk ID: 1000

Trunk name: Telnyx Inbound

Company Name: Telnyx

Route Table: :0

Remote Port: 5060

Service Port: SIP Public Default 1:1

Aggregate Capacity: 1200

Average CPS Limit: 500

Authorized RPS: 500

Unauthorized RPS: 500

Group Policy: Round Robin

Digit Mapping Table: no-translation:0

Min Call Duration: 0

Max Call Duration: 43200

RTP TOS: B8

Direction: Both

Service State: inservice

Allow Direct Media: No

No Answer Timeout: 120 

No Ring Timeout: 30

Option Poll: Disable

Cause Code Profile: Default:0

Stop Route Profile: Default:0

PAI: Disable

Digit Translation & RN Handling:digit-translation---rn-handling-

Ingress & Egress: can be set to all

Outbound ANI: pass

Tech Prefix: default

Codec Info:codec-info-

Policy: enforced

Codec 1: g711u64k

Codec 2: None

Codec 3: None

Codec 4: None

Codec 5: None

Codec 6: None

Codec 7: None

Codec 8: None

Fqdns Info:fqdns-info-

Depending on which of our SIP Proxies and media servers you interact with, based on your location, we recommend reviewing our signalling IP addressesTelnyx Developers & media IP addressesTelnyx Developers

Signaling IP's:

SIP Signaling Addresses

Media IP's:

Media IP's

Click save as & then submit. Now we can work on the outbound trunk.

Resource Type: Outboundresource-type--outbound

Resource Type: Peering

Protocol: SIP

SIP Profile: SIP_Peering:0

General Info:general-info-

SIP Trunk ID: 1001

Trunk name: Telnyx Outbound

Company Name: Telnyx

Route Table: :0

Remote Port: 5060

Service Port: SIP Public Default 1:1

Aggregate Capacity: 1200

Average CPS Limit: 500

Authorized RPS: 500

Unauthorized RPS: 500

Group Policy: Round Robin

Digit Mapping Table: no-translation:0

Min Call Duration: 0

Max Call Duration: 43200

RTP TOS: B8

Direction: Both

Service State: inservice

Allow Direct Media: No

No Answer Timeout: 120 

No Ring Timeout: 30

Option Poll: Disable

Cause Code Profile: Default:0

Stop Route Profile: Default:0

PAI: Disable

Ingress & Egress: can be set to all

Outbound ANI: pass

Tech Prefix: default

Codec Info:codec-info-

Policy: enforced

Codec 1: g711u64k

Codec 2: None

Codec 3: None

Codec 4: None

Codec 5: None

Codec 6: None

Codec 7: None

Codec 8: None

Fqdns Info:fqdns-info-

Depending on which of our SIP Proxies and media servers you interact with, based on your location, we recommend reviewing our signalling IP addressesTelnyx Developers & media IP addressesTelnyx Developers.

Signaling IP's:

SIP Signaling Addresses

Media IP's: Media

Once the information has been filled in, click save as & submit to create the trunk so the configuration gets pushed to the Sansay.

Addtional Resourcesaddtional-resources

Review our getting started with the Mission Control Portal guideTelnyx Developers to make sure your Telnyx Mission Control Portal account is setup correctly!

Check out Sansay SBCTelnyx Developers for further information.


Can't find what you're looking for? Click the chat bubble at your lower right hand corner and start a chat!

Was this page helpful?was-this-page-helpful