Open SidemenuDocs
Docs
Close Sidemenu

How to Configure an EdgeMarc SBChow-to-configure-an-edgemarc-sbc

Requirements For Configuring Edgemarc SBCrequirements-for-configuring-edgemarc-sbc

You should have your SBC already set-up with your IP-PBX and have one or more clinets configured and running calls between them. If you need an over view of the EdgeMarc setup, take a look at their resourcesTelnyx Developers.

Let's get started!

Configure your Telnyx Mission Control Portal

Follow our quick guideTelnyx Developers to setting up your account in the Mission Control Portal before we move on to the EdgeMarc SBC configuration.

Configure your Edgemarc SBCconfigure-your-edgemarc-sbc

1. Define your SIP Settings

In order to configure the SIP server information, navigate to VoIP -> SIP. Enter the following information below:

SIP Server Address: sip.telnyx.com SIP Server Port: 5060 SIP Server Transport: UDP Use Custom Domain: Check the box SIP Server Domain: sip.telnyx.com Limit Inbound to listed Proxies: Check the box Limit Outbound to listed Proxies: Check the box

Define your SIP Trunk Registration: In order to configure the SIP trunk registration, navigate to VoIP ALG -> B2BUA.

You can then configure trunk registrations with the WAN side of the soft switch as-well as the registration mode for the PBX on the LAN side. This will allow for sending SIP messages from the WAN side inbound and for sending SIP messages to the WAN side outbound.

Navigate to the Trunking Devices section to configure the PBX's SIP registration mode.

To create a new entry for a trunking device, click the "New Row" button.

  • Input your PBX's name in the "Name" field.
  • Select the correlating PBX from the drop-down list of the "Model" field.
  • Select the IP radio button as the registration mode.
  • Enter the PBX's IP into the IP field.
  • Select the transport as UDP.
  • Input 5060 for the port number.

Once the information has been filled in, click update to create the Trunking Device for PBX. Then click submit at the bottom of the page so the configuration gets pushed to the EdgeMarc.

Define your EdgeMarc inbound rules

This will allow for sending SIP messages from the EdgeMarc to the PBX.

  • To create a new inbound rule entry, click the "New Row" button.
  • Type inbound into the name field of the inbound rule.
  • Send To: Select the Trunking Device radio button.
  • Select your PBX from the dropdown menu.

Once the information has been filled in, click update to create the default inbound rule to the PBX. Then click submit at the bottom of the page so the configuration gets pushed to the EdgeMarc.

Define your Edgemarc inbound matching rules

  • To create a new inbound rule entry, click the "New Row" button.
  • Direction: Select inbound from the dropdown menu.
  • Mode: Select BothModes from the dropdown menu.
  • Select the "default" radio button.
  • Action: Select inbound from the dropdown menu.

Define your Edgemarc outbound matching rules

  • To create a new outbound rule entry, click the "New Row" button.
  • Direction: Select outbound from the dropdown menu.
  • Mode: Select BothModes from the dropdown menu.
  • Select the "pattern" radio button.
  • Select "calling" from the dropdown menu.
  • Depending on your preference, you can allow all callers by entering "."
  • Alternatively, you can pattern match on partial caller numbers such as 1312270X
  • Source: Select "any" from the dropdown menu.
  • Action: Select outbound from the dropdown menu.

Once the information has been filled in, click update to create the pattern matching rules you've defined. Then click submit at the bottom of the page so the configuration gets pushed to the EdgeMarc.

For more help in setting up take a look at EdgeMarc SBC full guideTelnyx Developers for more detailed instructions.

Looking for something more?

Click the chat bubble at your lower right hand corner and start a chat with a member of our support team.

Was this page helpful?