How to Configure a Sansay SBC
How to configure your Mission Control Portal
Step by Step Guide
For step by step instructions on each of the requirements on the Telnyx Mission Control Portal, please follow this guide. Once you've configured your Telnyx account, you can now proceed to setup Sansay SBC following the guide below.
Sansay SBC Configuration
Step by Step Guide
You are now all set on the Mission Control Portal side and are ready to configure your Telnyx trunk within your Sansay SBC system.
Define your Resource Settings
In order to configure the SIP server information for inbound & outbound trunks, navigate to Resources -> and create two new resources, one for each trunk.
Resource Type: Inbound
Resource Type: Peering
Protocol: SIP
SIP Profile: SIP_Peering:0
General Info:
SIP Trunk ID: 1000
Trunk name: Telnyx Inbound
Company Name: Telnyx
Route Table: :0
Remote Port: 5060
Service Port: SIP Public Default 1:1
Aggregate Capacity: 1200
Average CPS Limit: 500
Authorized RPS: 500
Unauthorized RPS: 500
Group Policy: Round Robin
Digit Mapping Table: no-translation:0
Min Call Duration: 0
Max Call Duration: 43200
RTP TOS: B8
Direction: Both
Service State: inservice
Allow Direct Media: No
No Answer Timeout: 120
No Ring Timeout: 30
Option Poll: Disable
Cause Code Profile: Default:0
Stop Route Profile: Default:0
PAI: Disable
Digit Translation & RN Handling:
Ingress & Egress: can be set to all
Outbound ANI: pass
Tech Prefix: default
Codec Info:
Policy: enforced
Codec 1: g711u64k
Codec 2: None
Codec 3: None
Codec 4: None
Codec 5: None
Codec 6: None
Codec 7: None
Codec 8: None
Fqdns Info:
Depending on which of our SIP Proxies and media servers you interact with, based on your location, we recommend reviewing our signalling IP addresses & media IP addresses
Signaling IP's:
Media IP's:
Click save as & then submit. Now we can work on the outbound trunk.
Resource Type: Outbound
Resource Type: Peering
Protocol: SIP
SIP Profile: SIP_Peering:0
General Info:
SIP Trunk ID: 1001
Trunk name: Telnyx Outbound
Company Name: Telnyx
Route Table: :0
Remote Port: 5060
Service Port: SIP Public Default 1:1
Aggregate Capacity: 1200
Average CPS Limit: 500
Authorized RPS: 500
Unauthorized RPS: 500
Group Policy: Round Robin
Digit Mapping Table: no-translation:0
Min Call Duration: 0
Max Call Duration: 43200
RTP TOS: B8
Direction: Both
Service State: inservice
Allow Direct Media: No
No Answer Timeout: 120
No Ring Timeout: 30
Option Poll: Disable
Cause Code Profile: Default:0
Stop Route Profile: Default:0
PAI: Disable
Ingress & Egress: can be set to all
Outbound ANI: pass
Tech Prefix: default
Codec Info:
Policy: enforced
Codec 1: g711u64k
Codec 2: None
Codec 3: None
Codec 4: None
Codec 5: None
Codec 6: None
Codec 7: None
Codec 8: None
Fqdns Info:
Depending on which of our SIP Proxies and media servers you interact with, based on your location, we recommend reviewing our signalling IP addresses & media IP addresses.
Signaling IP's:
Media IP's:
Once the information has been filled in, click save as & submit to create the trunk so the configuration gets pushed to the Sansay.
Addtional Resources
Review our getting started with the Mission Control Portal guide to make sure your Telnyx Mission Control Portal account is setup correctly!
Check out Sansay SBC for further information.
Can't find what you're looking for? Click the chat bubble at your lower right hand corner and start a chat!